This is a guide which will install FreeNAS 9.10 under VMware ESXi and then using ZFS share the storage back to VMware. This is roughly based on Napp-It’s All-In-One design, except that it uses FreeNAS instead of OminOS.
This post has had over 160,000 visitors, thousands of people have used this setup in their homelabs and small businesses. I should note that I myself would not run FreeNAS virtualized in a production environments. But many have done so successfully. If you run into any problems and ask for help on the FreeNAS forums, I have no doubt that Cyberjock will respond with “So, you want to lose all your data?” So, with that disclaimer aside let’s get going:
This guide was originally written for FreeNAS 9.3, I’ve updated it for FreeNAS 9.10. Also, I believe Avago LSI P20 firmware bugs have been fixed and have been around long enough to be considered stable so I’ve removed my warning on using P20. Added sections 7.1 (Resource reservations) and 16.1 (zpool layouts) and some other minor updates.
1. Get proper hardware
Example 1: Supermicro 2U Build
SuperMicro X10SL7-F (which has a built in LSI2308 HBA).
6 hotswap bays with 2TB HGST HDDs (I use RAID-Z2)
4 2.5″ hotswap bays. 2 Intel DC S3700’s for SLOG / ZIL, and 2 drives for installing FreeNAS (mirrored)
Example 2: Mini-ITX Datacenter in a Box Build
X10SDV-F (build in Xeon D-1540 8 core broadwell
IBM 1015 / LSI 9220-8i HBA
4 hotswap bays with 2TB HGST HDDs (I use RAID-Z)
2 Intel DC S3700’s. 1 for SLOG / ZIL, and one to boot ESXi and install FreeNAS to.
Hard drives. See info on my Hard Drives for ZFS post.
The LSI2308/M1015 has 8 ports, I like do to two DC S3700s for a striped SLOG device and then do a RAID-Z2 of spinners on the other 6 slots. Also get one (preferably two for a mirror) drives that you will plug into the SATA ports (not on the LSI controller) for the local ESXi data store. I’m using DC S3700s because that’s what I have, but this doesn’t need to be fast storage, it’s just to put FreeNAS on.
2. Flash HBA to IT Firmware
As of FreeNAS 9.3.1 or greater you should be flashing to IT mode P20 (looks like it’s P21 now but it’s not available by every vendor yet).
I strongly suggest pulling all drives before flashing.
LSI 2308 IT firmware for Supermicro
Here’s instructions to flash the firmware: http://hardforum.com/showthread.php?t=1758318
Supermicro firmware: ftp://ftp.supermicro.com/Driver/SAS/LSI/2308/Firmware/IT/
For IBM M1015 / LSI Avago 9220-8i
Instructions for flashing firmware:
LSI / Avago Firmware: http://www.avagotech.com/products/server-storage/host-bus-adapters/sas-9211-8i#downloads
(If you already have the card passed through to FreeNAS via VT-d (steps 6-8) you can actually flash the card from FreeNAS using the sas2flash utility using the steps below (in this example my card is already in IT mode so I’m just upgrading it):
[root@freenas] # cd /root/
[root@freenas] # mkdir m1015
[root@freenas] # cd m1015/
[root@freenas] # wget http://docs.avagotech.com/docs-and-downloads/host-bus-adapters/host-bus-adapters-common-files/sas_sata_6g_p20/9211-8i_Package_P20_IR_IT_FW_BIOS_for_MSDOS_Windows.zip
[root@freenas] # chmod +x /usr/local/sbin/sas2flash
[root@freenas] # sas2flash -o -f Firmware/HBA_9211_8i_IT/2118it.bin -b sasbios_rel/mptsas2.rom
LSI Corporation SAS2 Flash Utility
Version 16.00.00.00 (2013.03.01)
Copyright (c) 2008-2013 LSI Corporation. All rights reserved
Advanced Mode Set
Adapter Selected is a LSI SAS: SAS2008(B2)
Executing Operation: Flash Firmware Image
Firmware Image has a Valid Checksum.
Firmware Version 20.00.07.00
Firmware Image compatible with Controller.
Valid NVDATA Image found.
NVDATA Version 14.01.00.00
Checking for a compatible NVData image...
NVDATA Device ID and Chip Revision match verified.
NVDATA Versions Compatible.
Valid Initialization Image verified.
Valid BootLoader Image verified.
Beginning Firmware Download...
Firmware Download Successful.
Firmware Flash Successful.
(Wait a few minutes, at this point FreeNAS finally crashed. Poweroff. FreeNAS, and then reboot VMware)
Warning on P20 buggy firmware:
Some earlier versions of the P20 firmware were buggy, so make sure it’s version P20.00.04.00 or later. If you can’t P20 in aversion later than P20.00.04.00 then use P19 or P16.
3. Optional: Over-provision ZIL / SLOG SSDs.
If you’re going to use an SSD for SLOG you can over-provision them. You can boot into an Ubuntu LiveCD and use hdparm, instructions are here: https://www.thomas-krenn.com/en/wiki/SSD_Over-provisioning_using_hdparm You can also do this after after VMware is installed by passing the LSI controller to an Ubuntu VM (FreeNAS doesn’t have hdparm). I usually over-provision down to 8GB.
Update 2016-08-10: But you may want to only go to 20GB depending on your setup! One of my colleagues discovered 8GB over-provisioning wasn’t even maxing out 10Gb network (remember, every write to VMware is a sync so it hits the ZIL no matter what) with 2 x 10Gb fiber lagged connections between VMware and FreeNAS. This was on an HGST 840z so not sure if the same holds true for the Intel DC S3700… and it wasn’t virtualized setup. But thought I’d mention it here.
4. Install VMware ESXi 6
The free version of the hypervisor is here. http://www.vmware.com/products/vsphere-hypervisor. I usually install it to a USB drive plugged into the motherboard’s internal header.
Under configuration, storage, click add storage. Choose one (or two) of the local storage disks plugged into your SATA ports (do not add a disk on your LSI controller).
5. Create a Virtual Storage Network.
For this example my VMware management IP is 10.2.0.231, the VMware Storage Network ip is 10.55.0.2, and the FreeNAS Storage Network IP is 10.55.1.2.
Create a virtual storage network with jumbo frames enabled.
VMware, Configuration, Add Networking. Virtual Machine…
Create a standard switch (uncheck any physical adapters).
Add Networking again, VMKernel, VMKernel… Select vSwitch1 (which you just created in the previous step), give it a network different than your main network. I use 10.55.0.0/16 for my storage so you’d put 10.55.0.2 for the IP and 255.255.0.0 for the netmask.
Some people are having trouble with an MTU of 9000. I suggest leaving the MTU at 1500 and make sure everything works there before testing an MTU of 9000. Also, if you run into networking issues look at disabling TSO offloading (see comments).
Under vSwitch1 go to Properties, select vSwitch, Edit, change the MTU to 9000. Answer yes to the no active NICs warning.
Then select the Storage Kernel port, edit, and set the MTU to 9000.
6. Configure the LSI 2308 for Passthrough (VT-d).
Configuration, Advanced Settings, Configure Passthrough.
Mark the LSI2308 controller for passthrough.
You must have VT-d enabled in the BIOS for this to work so if it won’t let you for some reason check your BIOS settings.
7. Create the FreeNAS VM.
Download the FreeNAS ISO from http://www.freenas.org/download-freenas-release.html
Create a new VM, choose custom, put it on one of the drives on the SATA ports, Virtual Machine version 11, Guest OS type is FreeBSD 64-bit, 1 socket and 2 cores. Try to give it at least 8GB of memory. On Networking give it two adapters, the 1st NIC should be assigned to the VM Network, 2nd NIC to the Storage network. Set both to VMXNET3.
SCSI controller should be the default, LSI Logic Parallel.
Choose Edit the Virtual Machine before completion.
If you have a second local drive (not one that you’ll use for your zpool) here you can add a second boot drive for a mirror.
Before finishing the creation of the VM click Add, select PCI Devices, and choose the LSI 2308.
And be sure to go into the CD/DVD drive settings and set it to boot off the FreeNAS iso. Then finish creation of the VM.
7.1 FreeNAS VM Resource allocation
Also, since FreeNAS will be driving the storage for the rest of VMware, it’s a good idea to make sure it has a higher priority for CPU and Memory than other guests. Edit the virtual machine, under Resources set the CPU Shares to “High” to give FreeNAS a higher priority, then under Memory allocation lock the guest memory so that VMware doesn’t ever borrow from it for memory ballooning. You don’t want VMware to swap out ZFS’s ARC (memory read cache).
8. Install FreeNAS.
Boot of the VM, install it to your SATA drive (or two of them to mirror boot).
After it’s finished installing reboot.
9. Install VMware Tools.
SKIP THIS STEP. As of FreeNAS 9.10.1 installing VMware should may no longer be necessary–you can skip step 9 and go to 10. Just leaving this for historical purposes.
In VMware right-click the FreeNAS VM, Choose Guest, then Install/Upgrade VMware Tools. You’ll then choose interactive mode.
Mount the CD-ROM and copy the VMware install files to FreeNAS:
# mkdir /mnt/cdrom
# mount -t cd9660 /dev/iso9660/VMware\ Tools /mnt/cdrom/
# cp /mnt/cdrom/vmware-freebsd-tools.tar.gz /root/
# tar -zxmf vmware-freebsd-tools.tar.gz
# cd vmware-tools-distrib/lib/modules/binary/FreeBSD9.0-amd64
# cp vmxnet3.ko /boot/modules
Once installed Navigate to the WebGUI, it starts out presenting a wizard, I usually set my language and timezone then exit the rest of the wizard.
Under System, Tunables…
Add a Tunable. Variables should be: vmxnet3_load. The type should be Loader and the Value YES .
Reboot FreeNAS. On reboot you should notice that the VMXNET3 NICS now work (except the NIC on the storage network can’t find a DHCP server, but we’ll set it to static later), also you should notice that VMware is now reporting that VMware tools are installed.
If all looks well shutdown FreeNAS (you can now choose Shutdown Guest from VMware to safely power it off), remove the E1000 NIC and boot it back up (note that the IP address on the web gui will be different).
10. Update FreeNAS
Before doing anything let’s upgrade FreeNAS to the latest stable under System Update.
This is a great time to make some tea.
Once that’s done it should reboot. Then I always go back again and check for updates again to make sure there’s nothing left.
11. SSL Certificate on the Management Interface (optional)
On my DHCP server I’ll give FreeNAS a static/reserved IP, and setup an entry for it on my local DNS server. So for this example I’ll have a DNS entry on my internal network for stor1.b3n.org.
If you don’t have your own internal Certificate Authority you can create one right in FreeNAS:
System, CAs, Create internal CA. Increase the key length to 4096 and make sure the Digest Algorithm is set to SHA256.
Click on the CA you just created, hit the Export Certificate button, click on it to install the Root certificate you just created on your computer. You can either install it just for your profile or for the local machine, I usually do local machine, and you’ll want to make sure to store it is in the Trusted Root Certificate Authorities store.
Just a warning, that you must keep this Root CA guarded, if a hacker were to access this he could generate certificates to impersonate anyone (including your bank) to initiate a MITM attack.
Also Export the Private Key of the CA and store it some place safe.
Now create the certificate…
System, Certificates, Create Internal Certificate. Once again bump the key length to 4096. The important part here is the Common Name must match your DNS entry. If you are going to access FreeNAS via IP then you should put the IP address in the Common Name field.
System, Information. Set the hostname to your dns name.
System, General. Change the protocol to HTTPS and select the certificate you created. Now you should be able to go to use https to access the FreeNAS WebGUI.
12. Setup Email Notifications
Account, Users, Root, Change Email, set to the email address you want to receive alerts (like if a drive fails or there’s an update available).
Show console messages in the footer. Enable (I find it useful)
Fill in your SMTP server info… and send a test email to make sure it works.
13. Setup a Proper Swap
FreeNAS by default creates a swap partition on each drive, and then stripes the swap across them so that if any one drive fails there’s a chance your system will crash. We don’t want this.
Swap size on each drive in GiB, affects new disks only. Setting this to 0 disables swap creation completely (STRONGLY DISCOURAGED). Set this to 0.
Open the shell. This will create a 4GB swap file (based on https://www.freebsd.org/doc/handbook/adding-swap-space.html)
dd if=/dev/zero of=/usr/swap0 bs=1m count=4096
chmod 0600 /usr/swap0
If you are on FreeNAS 9.10
System, Tasks, Add Init/Shutdown Script, Type=Command. Command:
echo "md99 none swap sw,file=/usr/swap0,late 0 0" >> /etc/fstab && swapon -aL
When = Post Init
If you are on FreeNAS 9.3
System, Tunables, Add Tunable.
Variable=swapfile, Value=/usr/swap0, Type=rc.conf
Back to Both:
Next time you reboot on the left Navigation pane click Display System Processes and make sure the swap shows up. If so it’s working.
14. Configure FreeNAS Networking
Setup the Management Network (which you are currently using to connect to the WebGUI).
Network, Interfaces, Add Interface, choose the Management NIC, vmx3f0, and set to DHCP.
Setup the Storage Network
Add Interface, choose the Storage NIC, vmx3f1, and set to 10.55.1.2 (I setup my VMware hosts on 10.55.0.x and ZFS servers on 10.55.1.x), be sure to select /16 for the netmask. And set the mtu to 9000.
Open a shell and make sure you can ping the ESXi host at 10.55.0.2
Reboot. Let’s make sure the networking and swap stick.
15. Hard Drive Identification Setup
Label Drives. FreeNAS is great at detecting bad drives, but it’s not so great at telling you which physical drive is having an issue. It will tell you the serial number and that’s about it. But how confident are you in knowing which drive fails? If FreeNAS tells you that disk da3 (by the way, all these da numbers can change randomly) is having an issue how do you know which drive to pull? Under Storage, View Disks, you can see the serial number, this still isn’t entirely helpful because chances are you can’t see the serial number without pulling a drive. So we need to map them to slot numbers or labels of some sort.
There are two ways you can deal with this. The first, and my preference, is sas2ircu. Assuming you connected the cables between the LSI 2308 and the backplane in proper sequence sas2ircu will tell you the slot number the drives are plugged into on the LSI controller. Also if you’re using a backplane with an expander that supports SES2 it should also tell you which slots the drives are in. Try running this command:
# sas2ircu 0 display|less
You can see that it tells you the slot number and maps it to the serial number. If you are comfortable that you know which physical drive each slot number is in then you should be okay.
If not, the second method, is remove all the drives from the LSI controller, and put in just the first drive and label it Slot 0 in the GUI by clicking on the drive, Edit, and enter a Description.
Put in the next drive in Slot 1 and label it, then insert the next drive and label it Slot 2 and so on…
The Description will show up in FreeNAS and it will survive reboots. it will also follow the drive even if you move it to a different slot. So it may be more appropriate to make your description match a label on the removable trays rather than the bay number.
It doesn’t matter if you label the drives or use sas2ircu, just make sure you’re confident that you can map a serial number to a physical drive before going forward.
16.1 Choose Pool Layout
For high performance the best configuration is to maximize the number of VDEVs by creating mirrors (essentially RAID-10). That said, with my 6-drive RAID-Z2 array with 2 DC S3700 SSDs for SLOG/ZIL my setup performs very well with VMware in my environment. If you’re running heavy random I/O mirrors are more important, but if you’re just running a handful of VMs RAID-Z / RAID-Z2 will probably offer great performance as long as you have a good SSD for SLOG device. I like to start double parity at 5 or 6 disk VDEVs, and triple parity at 9 disks. Here some some sample configurations:
Example zpool / vdev configurations
2 disks = 1 mirror
3 disks = RAID-Z
4 disks = RAID-Z or 2 mirrors
5 disks = RAID-Z, or RAID-Z2, or 2 mirrors with hot spare.
(Don’t configure 5 disks with 4 drives being in RAID-Z plus 1 hot spare–that’s just ridiculous. Make it a RAID-Z2 to begin with).
6 disks = RAID-Z2, or 3 mirrors
7 disks = RAID-Z2, or 3 mirrors plus hot spare
8 disks = RAID-Z2, or 4 mirrors
9 disks = RAID-Z3, or 4 mirrors plus hot spare
10 disks = RAID-Z3, 2 vdevs of 5 disk RAID-Z2 or 5 mirrors
11 disks = RAID-Z3, 2 vdevs of 5 disk RAID-Z2 plus hot spare or 5 mirrors with hot spare
12 disks = 2 vdevs of 6 disk RAID-Z2, or 5 mirrors with 2 hot spares
13 disks = 2 vdevs of 6 disk RAID-Z2 plus hot spare or 5 mirrors with one hot spare
14 disks = 2 vdevs of 7 disk RAID-Z2 or 6 mirrors plus 2 hot spares
15 disks = 3 vdevs of 5 disk RAID-Z2 or 7 mirrors with 1 hot spare
16 disks = 3 vdevs of 5 disk RAID-Z2 plus hot spare or 7 mirrors with 2 hot spares
17 disks = 3 vdevs of 5 disk RAID-Z2 plus hot spares or 7 mirrors with 3 hot spares
18 disks = 2 vdevs of 9 disk RAID-Z3, 3 vdevs of 6 disk RAID-Z2 or 8 mirrors with 2 hot spares
19 disks = 2 vdevs of 9 disk RAID-Z3, 3 vdevs of 6 disk RAID-Z2 plus hot spares or 8 mirrors with 3 hot spares
20 disks = 2 vdevs of 10 disk RAID-Z3 4 vdevs of 5 disk RAID-Z2 plus hot spares or 9 mirrors with 2 hot spares
Anyway, that gives you a rough idea. The more vdevs the better random performance. It’s always a balance between capacity, performance, and safety.
16.2 Create the Pool.
Storage, Volumes, Volume Manager.
Click the + next to your HDDs and add them to the pool as RAID-Z2.
Click the + next to the SSDs and add them to the pool. By default the SSDs will be on one row and two columns. This will create a mirror. If you want a stripe just add one Log device now and add the second one later. Make certain that you change the dropdown on the SSD to “Log (ZIL)” …it seems to lose this setting anytime you make any other changes so change that setting last. If you do not do this you will stripe the SSD with the HDDs and possibly create a situation where any one drive failure can result in data loss.
Back to Volume manager and add the second Log device…
I have on numerous occasions had the Log get changed to Stripe after I set it to Log, so just double-check by clicking on the top level tank, then the volume status icon and make sure it looks like this:
17. Create an NFS Share for VMware
You can create either an NFS share, or iSCSI share (or both) for VMware. First here’s how to setup an NFS share:
Storage, Volumes, Select the nested Tank, Create Data Set
Be sure to disable atime.
Sharing, NFS, Add Unix (NFS) Share. Add the vmware_nfs dataset, and grant access to the storage network, and map the root user to root.
Answer yes to enable the NFS service.
In VMware, Configuration, Add Storage, Network File System and add the storage:
And there’s your storage!
18. Create an iSCSI share for VMware
WARNING: Note that at this time, based on some of the comments below with people having connection drop issues on iSCSI I suggest testing with heavy concurrent loads to make sure it’s stable. Watch dmesg and /var/log/messages on FreeNAS for iSCSI timeouts. Personally I use NFS. But here’s how to enable iSCSI:
Storage, select the nested tank, Create Zvol. Be sure compression is set to lz4. Check Sparse Volume. Choose advanced mode and optionally change the default block size. I use 64K block-size based on some benchmarks I’ve done comparing 16K (the default), 64K, and 128K. 64K blocks didn’t really hurt random I/O but helped some on sequential performance, and also gives a better compression ratio. 128K blocks had the best better compression ratio but random I/O started to suffer so I think 64K is a good middle-ground. Various workloads will probably benefit from different block sizes.
Sharing, Block (iSCSI), Target Global Configuration.
Set the base name to something sensible like: iqn.2011-03.org.b3n.stor1.istgt Set Pool Available Space Threshold to 60%
Portals tab… add a portal on the storage network.
Initiator. Add Initiator.
Targets. Add Target.
Extents. Add Extent.
Associated Targets. Add Target / Extent.
Under Services enable iSCSI.
In VMware Configutration, Storage Adapters, Add Adapter, iSCSI.
Select the iSCSI Software Adapter in the adapters list and choose properties. Dynamic discovery tab. Add…
Close and re-scan the HBA / Adapter.
You should see your iSCSI block device appear…
Configuration, Storage, Add Storage, Disk/LUN, select the FreeBSD iSCSi Disk,
19. Setup ZFS VMware-Snapshot coordination.
This will coordinate with VMware to take clean snapshots of the VMs whenever ZFS takes a snapshot of that dataset.
Storage. Vmware-Snapshot. Add VMware-Snapshot. Map your ZFS dataset to the VMware data store.
ZFS / VMware snapshots of NFS example.
ZFS / VMware snapshots of iSCSI example.
20. Periodic Snapshots
Add periodic snapshot jobs for your VMware storage under Storage, Periodic Snapshot Tasks. You can setup different snapshot jobs with different retention policies.
21. ZFS Replication
If you have a second FreeNAS Server (say stor2.b3n.org) you can replicate the snapshots over to it. On stor1.b3n.org, Replication tasks, view public key. copy the key to the clipboard.
On the server you’re replicating to, stor2.b3n.org, go to Account, View Users, root, Modify User, and paste the public key into the SSH public Key field. Also create a dataset called “replicated”.
Back on stor1.b3n.org:
Add Replication. Do an SSH keyscan.
And repeat for any other datasets. Optionally you could also just replicate the entire pool with the recursive option.
22. Automatic Shutdown on UPS Battery Failure (Work in Progress)
The goal is on power loss, before the battery fails to shutdown all the VMware guests including FreeNAS. So far all I have gotten is the APC working with VMware. Edit the VM settings and add a USB controller, then add a USB device and select the UPS, in my case a APC Back-UPS ES 550G. Power FreeNAS back on.
On the shell type:
<span class="shell_ff shell_be">ugen0.4: <APC> at usbus0 </span>
This will tell you where the APC device is. IN my case it’s showing up on ugen0.4. I ended up having to grant world access to the UPS…
chmod 777 /dev/ugen0.4
For some reason I could not get the GUI to connect to the UPS, I can selected ugen0.4, but under the drivers dropdown I just have hyphens —— … I set it manually in /usr/local/etc/nut/ups.conf
driver = usbhid-ups
port = /dev/ugen0.4
desc = "APC 1"
However, this file gets overwritten on reboot, and also the rc.conf setting doesn’t seem to stick. I added this tunable to get the rc.conf setting…
And I created my ups.conf file in /mnt/tank/ups.conf. Then I created a script to stop the nut service, copy my config file and restart the nut service in /mnt/tank/nutscript.sh
service nut stop
cp /mnt/tank/ups.conf /usr/local/etc/nut/ups.conf
service nut start
Then under tasks, Init/Shutdown Scripts I added a task to run the script post init.
Next step is to configure automatic shutdown of the VMware server and all guests on it… I have not done this yet.
There’s a couple of approaches to take here. One is to install a NUT client on the ESXi, and the other is to have FreeNAS ssh into VMware and tell it to shutdown. I may update this section later if I ever get around to implementing it.
Before going live make sure you have adequate backups! You can use ZFS replication with a fast link. For slow network connections Rsync will work better (Took under Tasks -> Rsync tasks) or use a cloud service like CrashPlan. Here’s a nice CrashPlan on FreeNAS Howto.
BACKUPS BEFORE PRODUCTION. I can’t stress this enough, don’t rely on ZFS’s redundancy alone, always have backups (one offsite, one onsite) in place before putting anything important on it.
Setup Complete… mostly.
Well, that’s all for now.